# $Id: Bonito,v 1.1.1.1 2006/09/14 01:59:09 root Exp $ # #	GENERIC configuration for Galileo EV64240 # #  This file is supposed to be included by target file after #  endian has been defined.
#
machine         LS2H        mips    # CPU Architecture, Platform
config          pmon 
option          VGAROM_IN_BIOS

option		LOONGSON_2H
option         	BOOT_PARAM
option      	VRAM_SIZE=16
#
#  Define target endian
#
makeoptions	ENDIAN=EL		# Little endian version.


#include "conf/GENERIC_ALL"

#
# System Name and Target Name
#
option		SYSTYPE="\"FCR\""
option		TARGETNAME="\"FCR\""

#
# Platform options
#
option		BONITOEL	
option		DEVBD2E
option		MIPS
option		INET

option      LS2HMC
option		ARB_LEVEL		# for MC parameters train
option		DDR3_DIMM		

#<<<<<<<<<<<<<<
###these options can NOT defined at the same time
#option		DDR3_SODIMM #1Rx8 2GB
#option		DDR3_SMT    #for SMT x16 SDRAM 4 chip 2GB
#>>>>>>>>>>>>>>

#option		AUTO_DDR_CONFIG		# for DIMM recognize
#option		I2C_CONTROL1		# select I2C control

select		mod_flash_amd		# AMD flash device programming
select		mod_flash_intel		# intel flash device programming
select		mod_flash_sst		# intel flash device programming
select		mod_debugger		# Debugging module
select		mod_symbols		# Symbol table handling
select		mod_s3load		# Srecord loading
#select		mod_fastload		# LSI Fastload
select		mod_elfload		# ELF loading
select		mod_txt

#
# Command selection. Selects pmon commands
#
select		cmd_newmt
select		cmd_setup
select		cmd_about		# Display info about PMON
select		cmd_boot		# Boot wrapper
select		cmd_mycmd
#select		cmd_mycmd_debug
select		cmd_newmt
select		cmd_cache		# Cache enabling
#select		cmd_call		# Call a function command
select		cmd_date		# Time of day command
select		cmd_env			# Full blown environment command set
select		cmd_flash		# Flash programming cmds
select		cmd_hist		# Command history
select		cmd_ifaddr		# Interface address command
select		cmd_l			# Disassemble
select		cmd_mem			# Memory manipulation commands
select		cmd_more		# More paginator
select		cmd_mt			# Simple memory test command
select		cmd_misc		# Reboot & Flush etc.
#select		cmd_stty		# TTY setings command
select		cmd_tr			# Host port-through command
select		cmd_devls		# Device list
select		cmd_set			# As cmd_env but not req. cmd_hist
select		cmd_testdisk
select		cmd_test
select		cmd_main
#
select		cmd_shell		# Shell commands, vers, help, eval
#
#
# Platform options
#
select		mod_uart_ns16550	# Standard UART driver
select		mod_display
option		CONS_BAUD=B115200
select		ext2
select		fatfs
select		ramfiles
select		mod_x86emu		# X86 emulation for VGA
option		MY40IO
#select		mod_x86emu_int10
option		MY61IO
#option          VGA_BASE=0xb0000000
select		mod_vgacon
#select		sis315e
#option		SIS315E
option		VGA_NO_ROM       # display card has no rom
#select		mod_sisfb
option		NOPCINAMES		# Save some space for x86emu
option		NOPCI
#option		FASTBOOT
#select		vt82c686        #via686a/b code

select		mod_framebuffer
option		X800x600
option 		CONFIG_VIDEO_16BPP
#option 	CONFIG_VIDEO_8BPP_INDEX

#
# Functional options.
#
option		NOSNOOP			# Caches are no-snooping

#
# HAVE options. What tgt level provide
#
option		HAVE_TOD		# Time-Of-Day clock
option		HAVE_NVENV		#  Platform has non-volatile env mem
option		HAVE_LOGO		# Output splash logo
option		USE_SUPERIO_UART
#option      	VESAFB
#option		USE_LEGACY_RTC
#option		GODSONEV2A
#option		LINUX_PC
#option		LONGMENG
#option		RADEON7000
#option 	DEBUG_EMU_VGA
option		AUTOLOAD
#option		CONFIG_PCI0_LARGE_MEM	
#option		CONFIG_PCI0_HUGE_MEM	
#option		CONFIG_PCI0_GAINT_MEM	
option		CONFIG_CACHE_64K_4WAY
option		NVRAM_IN_FLASH	

option		ACPI_S3_MODE
option      	SET_DDR_FREQ
option	    DDRFREQ=300
option	    CPUFREQ=800
#option      BOOT_FROM_NAND
#option      NAND_ECC_MODE
#
#  Now the Machine specification
#
mainbus0        at root
localbus0	at mainbus0
#fd0		at mainbus0
pcibr0		at mainbus0
#pcibr1		at mainbus0
pci*		at pcibr?
ppb*		at pci? dev ? function ?	# PCI-PCI bridges
pci*		at ppb? bus ?

lahci0		at localbus0 base 0xbfe30000	# AHCI
ahci_sd*  	at lahci0
ahci_cdrom*  	at lahci0
lohci0    	at localbus0 base 0xbfe08000	# OHCI
usb*      	at lohci0
#### USB
#uhci*		at pci? dev ? function ?

#### SCSI support
#siop*		at pci? dev ? function ?	# Symbios/NCR 53c...
#scsibus*	at siop?
#sd*		at scsibus? target ? lun ? 
#cd*		at scsibus? target ? lun ? 

#### Networking Devices
#gt0		at localbus? base 4
#gt1		at localbus? base 5
#gt2		at localbus? base 6

# fxp normally only used for debugging (enable/disable both)
#fxp*		at pci? dev ? function ?        # Intel 82559 Device
#inphy*		at mii? phy ?                   # Intel 82555 PHYs
#rtl*		at pci? dev ? function ?
#rtk*		at pci? dev ? function ?
#em*		at pci? dev ? function ?
#uhci*		at pci? dev ? function ?
#ohci0		at pci? dev ? function ?
#usb*		at usbbus ? 
#ohci1		at pci? dev ? function ?

select		mod_usb
select  	mod_usb_storage
select		mod_usb_uhci
select 	 	mod_usb_ohci
select		mod_usb_kbd


#### IDE controllers
pciide* 	at pci ? dev ? function ? flags 0x0000
#atp*           at pci? dev ? function ?  #sata atp8620
#wd*		at atp? channel ? drive ? flags 0x0000
#sata*		at atp?

#### IDE hard drives
wd0		at pciide? channel ? drive ? flags 0x0000
cmdide*		at pci ? dev ? function ? flags 0x0000
wd*		at cmdide? channel ? drive ? flags 0x0000

#### Pseudo devices
pseudo-device	loop	1	# network loopback

syn0		at localbus0
syn1		at localbus0
select		gmac

ide_cd* 	at pciide? channel ? drive ? flags 0x0001
select 		iso9660
option		IDECD 
select		cmd_testfire
#option		HAVE_NB_SERIAL
#option		USE_ENVMAC
#option		LOOKLIKE_PC
#select		cmd_lwdhcp
#select		cmd_bootp
option		FOR_GXEMUL
select		fatfs
#option		FLOATINGPT
option		COM3_BASE_ADDR=0xbfe001e0
#option		WDC_NORESET
select		gzip
option		INPUT_FROM_BOTH
option		OUTPUT_TO_BOTH
option		KBD_CHECK_FAST
option		TEST_USB_HOST
option		CONFIG_SLOW_PCI_FOR_BROKENDEV
option 		CONFIG_VIDEO_SW_CURSOR

select		http
select		tcp
select		inet
#select		nand
select		cmd_xyzmodem
#bellow for yanhua
#option BELL_PINS=0x8040
#option GPIO_SEL_UARTS=0xfc
#bellow for firewall
option GPIO_OUT_PINS=0xf00 
option GPIO_OUT_CLR=0xf00
option DIMM_ID=0x54
select switch
option GMAC_CONNECT_TO_SWITCH=0xbfe18000
#option		AUTO_DDR_CONFIG		# for DIMM recognize
option	HANDLE_NMI

#bellow for zd
#option		AUTO_DDR_CONFIG		# for DIMM recognize
#option		I2C_CONTROL1		# select I2C control
#option GPIO_OUT_PINS=0x1502
#option GPIO_OUT_CLR=0x1500
#option GPIO_OUT_SET=0x2
#option DIMM_ID=0x50

#bellow for zd pad

#option GPIO_OUT_PINS=0x3000
#option GPIO_OUT_SET=0x2000
#option GPIO_OUT_CLR=0x1000
#
#option DDR_S1=0xc1e18804
